Modular Linear Power Supplies up to 4 in a Rack
The RMQ Series power supplies provide pure linear regulated DC power designed to be used in lab bench, system application, R&D and production test. The RMQ Series provides full rated voltage or current at any setting without the need for derating.
These power supplies are provided with front panel binding posts and rear connector for ease in output wiring. The unit is also provided with
remote sense in the rear connector for excellent regulation at the point of load. Optional interface via IEEE-488, LAN, RS485 and RS232 allows for remote control.
- Digital Meters
- Remote Programmable
- Remote Sensing
- Series / Parallel Operation
- 1mV Ripple
- 1/4 Rack Modules
- 10 – Turn Voltage & Current Control
- Optional IEEE-488, LAN, RS485, RS232 Control
- Optional 4 Modules in Rack Mount Tray
|RMQ6-9A||0-6 V||0-9 A||0.01%||0.1%||0.01% or 1mV||0.1%|
|RMQ10-6A||0-10 V||0-6 A||0.01%||0.1%||0.01% or 1 mV||0.1%|
|RMQ20-3.3A||0-20 V||0-3.3 A||0.01%||0.1%||0.01% or 2 mV||0.1%|
|RMQ40-2.5A||0-40 V||0-2.5 A||0.01%||0.1%||0.01% or 4 mV||0.2%|
|RMQ60-0.9A||0-60 V||0-0.9 A||0.01%||0.1%||0.01% or 4 mV||0.2%|
|RMQ125-0.5A||0-125 V||0-0.5 A||0.01%||0.1%||0.01% or 4 mV||0.2%|
|RMQ200-0.4A||0–200 V||0-0.4 A||0.01%||0.1%||0.01% or 4 mV||0.2%|
|RMQ400-0.25A||0-400 V||0-0.25 A||0.01%||0.1%||0.01% or 6 mV||0.5%|
Input: 115 VAC ±10%, 50/60 Hz Single Phase.
Optional: 220 VAC ±10%, 50/60 Hz Single Phase.
Output: See specific model in table. The output is floating and either side may be grounded.
Load Regulation: See specific model in table. Regulation is for a full load step.
Line Regulation: See specific model in table. Regulation is for a line change from within specified input voltage range.
Ripple: ≤1 mV RMS.
Response Time: The output voltage is within regulation limits in less than 100 microseconds for a ½ load step. The output voltage will remain within regulation limits for input line step within specified voltage range.
Remote Sensing: Units provided with remote sense terminals at the rear for regulation at the point of load.
Remote Programming: All units are voltage programmable at approximately 1000 Ω / Volt except Model HWD400-0.5B which is programmable at 500 Ω / Volt.
Series / Parallel Operation: Two or more units may be operated in series. Two units with the same voltage and current may be operated in parallel.
Temp. Coef.: 0.02% / °C.
Stability: Better than 0.05%/8 hours at constant line, load and temperature after ½ hour warm up.
Operating Temperature: 0°C to +50°C at any combination of line, load and temperature without the need for external cooling.
Terminations: Circular connector is provided at the rear for
output, sensing and ground. 5 Way binding posts are provided on the front panel for output and ground. A 7’ 3-wire line cord is provided for AC Input.
Protection: The power supply is protected by a fuse in the input line. The unit is provided with OVP, OCP, CV to CC mode and CC to CV mode.
Panel Controls: Digital voltmeter, digital ammeter, 10 turn voltage control, 10 turn current control, pilot light, ON/OFF switch and five way binding posts. The voltage and current control are fully adjustable by means of 10 turn panel potentiometers.
Finish: The standard front panel and chassis finish is light blue. Chassis and cover are yellow-irridite.
Size: 5 ¼” H x 4⅛” W x 20¼” D.
Four units can be mounted in a 5¼“ x 19” rack mount tray.
|27||Chassis Slides (Available with 132 only)|
|108||RS232 Control with Readback|
|110||RS485 Control with Readback|
|112||IEEE-488 Control with Readback|
|123||RJ45 Control with Readback|
|132||RMQ 5¼” Rack Mount Assy (4 Position)|
CONNECTOR TABLE FOR MULTIPLE MODULES
|POWER SUPPLY MODEL||ME CONN PART #||PS CONNECTOR*||MATTING CONNECTOR**|
* Multiple position shell polarization to insure connectors can
be mated in only one possible orientation
** Optional mating connector.