High Voltage SCR Regulated Power Supply Up to 1500V
The KV series of power supplies are constant voltage/constant current units with automatic crossover. Models are available with up to 3 ampere current capacity over the full voltage range. Options such as remote voltage programming, remote current programming and remote power control makes the unit a versatile equipment for laboratory and manufacturing operations.
- Output 0 to 1500 VDC
- 0.5% Voltage Regulation
- 0.5% Current Regulation
- 0.5% RMS Ripple
- Standard Voltmeter and Ammeter
- Optional 3½ Digit Digital Meters
- Optional Voltage/Voltage Programmable
- Optional IEEE488, RS485, RS232 Control
5 ¼” Model
|KV1000-0.5||0-1000 V||0-0.5 A|
|KV1000-1||0-1000 V||0-1.0 A|
|KV1500-0.5||0-1500 V||0-0.5 A|
|KV1000-2||0-1000 V||0-2.0 A|
|KV1500-1||0-1500 V||0-1.0 A|
|KV1000-3||0-1000 V||0-3.0 A|
|KV1500-1.5||0-1500 V||0-1.5 A
[*10½” Model and above: 230 VAC 50/60Hz 3Ø Standard]
Input: 115 VAC or 230 VAC ±10%, 50/60 Hz single phase depending on the model.
Output: See specific model in table. Adustable 0 to rated voltage in voltage mode. Adustable 0 to rated current in current mode.
Line: ≤ 0.5% for a line change within specified input range.
Load: ≤ 0.5% for a full load step.
Line: ≤ 0.5% for a line change within specified input voltage range.
Load: ≤ 0.5% for full voltage compliance over the operating range of >10% to <90% of maximum rated output.
Ripple: ≤ 0.5% volts RMS of maximum rated output.
Response Time: The output voltage is within regulation limits in less than 500 miliseconds for a ½ load step.
- 10 – Turn Voltage Control
- 10 – Turn Current Control
- Input Fuse – KV 1000-0.5, KV 1000-1 and KV 1500-1.5 Circuit breaker – all other models
Operating Temperature: 0 to 50°C without derating.
Input: 5 ¼” & 7″ models have 3-wire line cords. All other models have a barrier terminal strip.
Output: Barrier terminal strip at the rear.
5¼” Model: 5¼” (H) x 19″ (W) x 16½” (D)
7″ Model: 7″ (H) x 19″ (W) x 16½” (D)
10½” Model: 10½” (H) x 19″ (W) x 16½” (D)
14″ Model: 14″ (H) x 19″ (W) x 16½” (D)
|6||Over Voltage Protection|
|29||Optional 220 VAC Input|
|36||Voltage/Voltage Programming (0-10V = Full Rated Output Voltage)|
|52||Voltage/Current Programming (0-10V = Full Rated Output Current)|
|62||3½ Digit Digital Meters|
|85||Voltage/Voltage Programming (Isolated Input 0-10V = Full Rated Voltage)|
|90||Voltage/Current Programming (Isolated Input 0-10V = Full Rated Current)|
|95||Remote Output Inhibit 5 V = DC ON, 0 V = DC OFF|
|108||RS232 Control with Readback|
|110||RS485 Control with Readback|
|112||IEEE-488 Control with Readback|
Other options available – Consult with factory